How To Change a Furnace Filter

February 20, 2020

Many homeowners underestimate the importance of changing furnace filters regularly. Clean furnace filters catch dust, pet dander and other particles. When your furnace filters are dirty, it decreases your energy efficiency. Changing your furnace filter is a simple DIY project. The only things you’ll need for this project are new furnace filters and about 10 minutes of your time. The following tips can help you replace your furnace filter in Thousand Oaks. Turn Off Your Furnace While you’re changing your filter, you don’t want the furnace to come on. That’s why it is a good idea to turn the furnace off. To maximize safety, you should unplug your furnace from the outlet. If you can’t reach the plug, turn off the power source to the furnace. Taking this step can prevent electrical shock or accidents. Find the Air Filter Panel Your furnace manual should contain information about the filter’s location. Can’t find your manual? Inspect your furnace to see if you can locate the air filter panel. In many furnaces, the panel is located near the metal ductwork or the blower. Once you’ve found the filter panel, open it and remove your old furnace filter. Change the Filter Compare your...

View Article

Read More

How To Light a Pilot Light on a Furnace

February 16, 2020

When your furnace goes out on a cold winter night, you need to get that pilot light lit again quickly. In this article, we intend to help you do just that. The brief discussion below will take you through the steps required to get your furnace’s pilot light lit once more. Carefully Check Out the Instruction Label on Your Furnace Look at the sides of your furnace. On one of the sides, you should find a label with instructions. On this label, you’ll find information to help you light the pilot light properly. This information will be specific to your furnace and pertain to your particular make and model. Try to locate this label if at all possible. Set the Pilot Light Dial to “Off” The next step is to look for the pilot light dial. This will generally be on the lower part of your home furnace. Once you’ve found it, you’ll notice that it has several settings, usually marked “On,” “Off” and “Pilot.” Next, simply turn that knob until it is set to the off position. Once you’ve done this, wait for approximately five minutes. This will be enough time to allow any gas to dissipate. Use a...

View Article

Read More

Why Does My Heating System Keep Turning Off?

November 11, 2019

Your furnace has several safety switches that are monitoring different conditions within the system. If they detect a problem, they will turn off your furnace to keep it from failing. If a safety switch turns off your furnace, the controller will wait a few minutes and restart the furnace. If a safety switch still detects a problem or is malfunctioning, it will turn off your furnace again. This cycle may continue until the problem is determined and fixed. A Diagnostic Test Will Find Your Furnace’s Problem Safety switches are monitoring airflow, heat buildup and the presence of a flame when fuel is being fed to your furnace. The skilled technicians at in Burbank, CA, can determine if a safety concern is present or if one of the sensors is beginning to fail. One of these sensors is monitoring the volume of air flowing through your furnace. Low airflow can cause the heat exchanger to overheat. An airflow problem might be caused by a dirty air filter, a dirty blower wheel, too many closed heat vents or an obstruction within the system. The flame sensor is ensuring that a flame is present when fuel is being fed to the ignition chamber....

View Article

Read More

Why Is My Heating System’s Filter Black?

November 1, 2019

Strange things can happen with a heating system. Unexpected mishaps may require service calls, and routine maintenance is also necessary at times. You should, therefore, expect to replace a filter at some point. When the screen becomes black, something is seriously out of the ordinary. Putting in a new filter might not be enough. Depending on the cause, other work may be required. Dirt Accumulates in the Filter The filter catches dirt and, eventually, becomes so dirty that it turns black. Changing it before this point would be best. If you waited too long to change it, get the work done now. If you live near Burbank, CA, you can turn to . ​ Mold Finds a Home Mold might not be the first thing you suspect when you see a black filter, but the organic growth may very well be the culprit. Mold can grow in any environment that’s hospitable to it. This includes the interior of a heater. If there’s dampness inside the heating system, any mold spores present are going to grow and feed. Once mold affixes to the filter, the organic matter on the screen will give mold a food source. The filter has to go....

View Article

Read More